Mini 4WD Wiki
Register
Advertisement
Mini 4WD Wiki
MSChassisLogo
MS Chassis

MS Chassis with N-02 nose and T-02 tail equipped.

The MS Chassis (Japanese: MSシャーシ, Emuesu Shāshi) is a Mini 4WD chassis introduced by Tamiya in November 2005. It was the first double-shaft motor-driven chassis, and it was marketed exclusively under the Mini 4WD PRO car line-up.

General info[]

Instead of placing the motor on the front or the rear, the motor was relocated to the middle of the chassis. In order to achieve this, Tamiya and SMC Motor co-developed a line of double-shaft motors for the new chassis, resulting in a 50/50 power transfer ratio. The batteries are now moved further to the sides of the chassis, with the motor itself in between.

The MS Chassis uses a modular design, divided into three main parts: the nose, centre and the tail. This allows for a variety of configurations, with three different nose and tail parts and two centre parts available. There also exists a bumper-less nose and tail module (N-03/T-03).

It has the short, 80 mm wheelbase as with most compact chassis, resulting in better cornering. As all wheels are directly driven by the motor without the need of a propeller shaft, the MS Chassis has better torque than any chassis released so far.

One downside of the MS Chassis is its weight, which can be mitigated by using lightweight center parts. Another disadvantage is that since the chassis' basic layout is by and large fundamentally different from traditional Mini 4WD (i.e. front and rear motor) chassis, only parts that are bespoke to the chassis are compatible. And due to the motor and battery being placed at the middle of the chassis, narrow track large-diameter wheels are no longer compatible.

The basic MS Chassis components would later reused and redeveloped in the MA Chassis.

Technical info[]

Chassis Data
Length 154 mm (With N-01)
152 mm (With N-02 and N-04)
Width 92 mm
Wheelbase 80 mm
Ground Clearance 4 mm (With large-diameter wheels)
1 mm (With low-profile small-diameter wheels)
Driveshaft Length 60 mm
72 mm (N-04 and T-04 only)
Compatible Gear Set(s) 4:1
3.7:1
3.5:1
Roller Down Thrust Angle 5
Terminal Type MS-type
Weight With batteries:
124 g
123 g
Without batteries:
70 g
Chassis Stats
Toughness 4.4 MSChassisStats
Acceleration 3.9
Cornering 4.9
Stability 3.9
Adaptability 4.5
Ease of Maintenance 3

Trivia[]

  • The N-04 and T-04 units were the only nose and tail units that require 72 mm drive shafts, which, up until then, was made exclusively for Super X Chassis.
  • It is the first Chassis to have the new double-shaft motor.
  • Some bodyshells made for earlier chassis require modifications in order to fit them into the MS Chassis.
    • At the launch of the MS Chassis car, Tamiya's staff accidentally listed Strato Vector (which required a front motor chassis) in the list of compatible bodyshells on the official website. It has been since removed.
  • In a patent Tamiya registered for the chassis, it shows that the chassis can be equipped with nose and tail units with different ground clearances and the nose unit can be swapped for the one with steering mechanism. It is unknown why Tamiya had scrapped those ideas for the actual chassis release.[1]

References[]

Chassis
Original series Origin · Comical · Wild · Cruiser · RV
Type series
(Racing/Truckin')
Type-1 · Type-2 · Type-3 · Type-4 · Zero · FM · Truckin' · Type-5
Super series
(Super/Mighty, Fully Cowled/Aero)
Super-1 · Super-FM · Super TZ · Super X · VS · Super TZ-X · Super XX · Super-II
Mini-F series Mini-F
R/C Mini 4WD TR-1
PRO/REV/Laser MS · AR · MA · FM-A · VZ
Advertisement